Home > Sundance Spa > Sundance Fl1 Error Code

Sundance Fl1 Error Code

Contents

Carlsbad: (760) 431-7727 | San Diego (858) 675-7727 Find Your Perfect Hot Tub J-500 Collection J-585™ Seats: 5-7 Jets: 52 J-575™ Seats: 5-6 Jets: 53 J-400 Collection J-415™ Seats: 2-3 Jets: We have a Bahia spa. We have turned the hot tub off and on numerous times and tried both filters with no luck. If the ICE msg does not go away please contact your local Spa dealer of the manufacturer of your spa to service your spa. weblink

The J-465 is a great spa or hot tub with many seat choices.The Jacuzzi Spa J-135 hot tub  is a 6 person entry level hot tub. See “Summer Log” below.3. Logged Trying to be the unbaised voice of reason. New filter, water level good, bled pump at housing fitting, weir gate inspected.

Sundance Spa Error Codes

System activates the heater and jets pump 1 to bring temp within 15°F (8°C) of settemps.No action required.Note: this condition often occurs when filling the spa with water since tap water If you have 240 vac +/- 10% here with a heat call and your circ pump just hums or is overly hot to the touch you may have a bad circ Re: Flash FL1 error code fixed « Reply #1 on: December 21, 2012, 05:49:32 PM » Logged Former HotSpring Dealer - Southern Cal. Patty Dechellis April 13, 2014 Reply I NEED A ANSWER??

Reset the countdown timer when finished.FL1 or FL2 (Flashing)When FL1 code starts flashing it means the flow switch is malfunctioning and stuck open-likely because of a dirty filter or because there Low speed jets pump 1 and optional circulation pump (if your spa is equipped) activates to circulate water through heater.DO NOT GET INTO THE WATER. 1. The J-385 has a large step to enter the hot tub that can be very useful in the evening.The Jacuzzi Spa J-325 hot tub spa is a 3-4 person hot tub. Sundance Spa Flo Error If all else fails contact your local Sundance Spas Support Desk to book a diagnostic and repair of your spa.

Nigel October 19, 2016 Reply Justin if the circulation pump is not turning, panel heat indicator light is not lit and the panel is flashing FL1 first check with your multimeter Jacuzzi Hot Tub Error Code Fl1 Add water if needed.2. Always turn off electricity before removing any equipment doors. They can agitate down and partially block flow also. Ask Your Own Pool and Spa Question Customer: replied3 years ago.

A month ago I replaced the filter, heater, flow switch, Hi-limit and temperature sensors. Sundance Spa Circulation Pump Problem The condition causes the circulation pump to turn off automatically if it’s running in order to avoid adding additional heat to spa water that could cause “Overheat” conditions. Hi my name isXXXXX will help you with this. Nigel October 20, 2016 Reply Justin correct me if I am wrong but you only have one pump on that model.

Jacuzzi Hot Tub Error Code Fl1

The J- 355 features 2 deep bucket seats, one lounge and is a deep sitting hot tub. That has to move and touch the round post on the left anytime the spa power is on after the initial start up sequence. Sundance Spa Error Codes The J- 470 features four deep bucket seats for the ultimate deep sitting hot tub. Sundance Flow Switch Possibly we are having the same issue you did.

If the FL1 error goes away with the filter removed it is time to soak the filter in some filter cleaner or replace it if it is a disposable filter (MicroClean). have a peek at these guys The filter looks clean, I've tried the hose in the fitting trick, but no air lock it seems. Could be that part of the plumbing is frozen or you have a bad temp sensor and or bad PWA. I will try the connections at the circ. Sundance Spa Flow Switch Testing

Email check failed, please try again Sorry, your blog cannot share posts by email. %d bloggers like this: You could wire your circ pump direct to incoming 230vac at TB1. Usually when I get an FL1 - it is the filter or the circ pump however when those issues happened, turning on the tub at least started the pump and the check over here Please try again.

What do I do? Sundance Spa Troubleshooting Forum It's only showing power … July 04, 2014 Reply Check the connections of both sensors where they enter the harness at J2. November 13, 2014 Reply Dustin the pump 2 button locks up during FL1.

If all else fails contact your local Sundance Spas Support Desk to book a diagnostic and repair of your Sundance Spa.

If you don't have continuity at the thermal disc try replacing the thermal disc and making another heat call. I will re-verify the flow switch. Look in the area where the filter is and see if there is a something that looks like a plug about 1/4" size or less anywhere. Sundance Spa Reset We are unsure what to do next.

The J- 575 features two deep bucket seats for the and one deep sitting lounge for best relaxation. The J-575 also has a nice step to enter the hot tub. we have turned the spa on and off - sometimes this fixes it, we have changed the filter which is clean. Try turning off your spa and unplugging your sensor harness J2 on your PWA and then re-applying power to the spa. http://cpresourcesllc.com/sundance-spa/sundance-spa-code-fl1.php April 13, 2014 Reply Patty normally the ICE msg comes up when a freeze condition is detected.

I assume I probably have a malfunctioning Flow Switch. Click on this link for all Sundance Spas Manuals:Sundance Spa Owner ManualsSundance Spas Tech Tips:Some of the most common error codes for Sundance and some tech tips to assist you: 1. I truly believe it's an airlock but I can't seem to aleviate the issue. Ran water into intake with rag wrapped around.

Check for proper water level.3. I tried all the recommended fixes, but no help.