Home > Sundance Spa > Sundance Spa Code Fl1

Sundance Spa Code Fl1

Contents

Next problem is the pump 2 wont turn on by pushing the button on top. I am having issues with my temp sensor and was about to replace it anyway when the FL1 happened 2 days ago and would not go away. TO reset your ClearRay timer, please refer to our "616" reset instructions here.   Contact UsName * E-Mail * Subject * Message * Download A Copy Of This  Here

© Copyright I can unsubscribe at any time. * Support TypesProblemsQuestions Support TopicsHot TubsAccessoriesControl Panel ErrorsHeat IssuesLeaksLightingOtherStereoWater Flow IssuesPoolsFiltersHeatersLeaksLinersOtherPool StructurePumpsSaltProblemsQuestionsWater CareCloudy WaterGreen WaterHot Tub WaterSalt Water Pools Hot Tubs Bathrooms Service Pool Renovations weblink

Turn your breaker back on without the filters in the spa. If you recently drained and refilled your Sundance Spa you could have an air lock. I can confirm that the board is in line with the schematic. Logged Trying to be the unbaised voice of reason.

Sundance Spa Error Codes

All jets work and have had water run into them. No current with a heat call and voltage at j9 and j10 would indicate a bad heater. Ask a Question or Comment Cancel reply Message *Name * Email * Phone Number * City * I agree to participate in this conversation via email. And kicks out and starts all over again please help.

Patty Dechellis April 13, 2014 Reply so should i turn the jets on? Nigel September 01, 2016 Reply Randy you want to use the hole opposite of the mesh side. http://www.spaandpoolsource.com/pdf/sun ... Sundance Spa Circulation Pump Problem Richmond, CA 94804 (510) 234-7920 Register Help Remember Me?

Check the voltage rating on the motor before applying voltage to the motor. Once the air lock is alleviated you should see water flow (bubbles) returning to your return heat jet (small grated fitting) in the footwell of your spa directly under your filter Logged clover Full Member Posts: 475 Re: Flash FL1 error code fixed « Reply #6 on: January 13, 2014, 10:43:55 PM » Quote from: schardenzar on January 12, 2014, 04:59:44 PMnothing If this doesn't do it, first check for proper voltage.

schardenzar Junior Member Posts: 3 Re: Flash FL1 error code fixed « Reply #7 on: January 13, 2014, 11:36:08 PM » Thank you for your help! Sundance Spa Flo Error thanks.. Most often this is caused by a dirty filter.The heater will not turn on when there is a FL1 error. Although you can't rule out a bad Flow switch when you see an FL1 msg you have no power at the circ pump assignment points, power can activate the the circ

Jacuzzi Hot Tub Error Code Fl1

Good luck. can any one help? Sundance Spa Error Codes If you are in an area with extremely warm conditions (i.e. Sundance Spa Flow Switch Testing It is also helpful sometimes to put your spa in economy mode to prevent overheating in the summer.

Could this be a flow switch issue, if so is there a way to eliminate the switch and verify that the pcb is functional and at the same time determine if http://cpresourcesllc.com/sundance-spa/sundance-error-code-616.php You could try to rotate the shaft by popping off the small access cover at the rear of the motor. If all else fails contact our Service Support Desk to book a diagnostic of your Sundance Spa. We have alot of people replace the high limit also and it could also be an issue.Because this is the most common issue and one that is the least expensive to Sundance Flow Switch

I have replaced the heater and temp sensor already, and just recently changed the water. If the FL1 error goes away with the filter removed it is time to soak the filter in some filter cleaner or replace it if it is a disposable filter (MicroClean). The problem is that the only shipping option was FedEx ground, which in reality meant Smartpost. check over here Remove your filters.

Check for proper water level.3. Sundance Spa Troubleshooting Forum You can also email us with specific details on what the spa does when you power the unit on and off and before it goes into watchdog mode. No water is circulating and the "heating tube" is cold however, the electric motor attached to the pump with the two main feed lines is very hot.

Still we have no circulation or heat.

If it doesn't go away you may have blockage in your circ line and or a bad Pressure switch. If all else fails contact your local Sundance Spas Support Desk to book a diagnostic and repair of your Sundance Chelsee Spa. Thanks Nigel October 26, 2015 Reply Robert what make and model spa do you have and what is the date built? Sundance Spa Reset Even with no power to the tub, the flow switch is making contact.

I think at this point since I'm neither handy or lucky, it may be easiest to replace the pump. Mr. I have also run the tub for a few minutes on pump 1 to see if that shakes the flow switch loose, it didn't clear the error. this content You should have 240vac +/- 10% with a 240vac setup.

It has disabled itself to prevent further damage. Possibly we are having the same issue you did.