Home > Sundance Spa > Sundance Spa Code Flo

Sundance Spa Code Flo

Contents

If TFP has helped you, please click to SUPPORT TFP! Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. This leads me to conclude that the pump is responsible in some way. Depending on where the temp sensor is mounted; usually in the wall of the spa in a sensor mount, you could have a flow issue. weblink

Remove filter and allow air to bleed out of filter. Sundance Altamar Hot Tub. If continuity is measured, switch is OK. You could simply check to be certain you're using an authorized dealer, and by phone ask to accelerate the shipping, though I personally haven't had issues with fedex ground.

Sundance Spa Error Codes

ArcticHotTubs 24.225 görüntüleme 1:25 Daha fazla öneri yükleniyor... We do not ship or sell outside of the USA! If you power the spa down and power it back up it may work for a while but will do the same thing again.

OPEN SENSOR (heater disabled) or SHORTED SENSOR (hot tub deactivated) The high-limit temperature sensor is non-functional. If there is no continuity, turn the main pump back on, if you then have continuity, then your Circulation Pump is suspect. That's just how it works for me. Sundance Spa Flow Switch Testing I can opertate it off the panel switch though, and there is flow.

Model is sm-909-nhw-18. Sundance Spa Flow Switch to2007.pdf 25,000 gallon in ground white plaster- 1 1/2 HP Pentair SuperFlo pump - 60 sqft FNS DE filter (with FiberClear), 1999 Sundance Optima 850 hot tub. We place a water hose where the filter normally sits and FLO message disappears. Yükleniyor...

strongtech1 89.327 görüntüleme 5:05 # 36 Why doesn't my hot tub work - Süre: 4:15. Sundance Spa Pressure Switch Just connected it 12/1/2016 12/1/2016 Poolservice123 The cal spa hot tube has two settings jet 1 and jet 2. Check for sticking or damaged weir gate.6. Sign Up All Content All Content Advanced Search Browse Forums Blogs Calendar Staff Online Users More Activity All Activity Search More More More All Activity Home Sorry, there is a problem

Sundance Spa Flow Switch

NOTE: The Hi Limit Sensor is located behind a shield on the stainless heater manifold and is the smaller of the two silver bullets. FWIW, I found that the tub is indeed a Capri, made in 1998. Sundance Spa Error Codes The switch operates a motion switch comprised of a solid center stem and a metal spring loaded vane that moving water moves to come in contact with the solid center stem Sundance Spa Flo2 Error I'm in love with it and can't wait to gain more knowledge and get this thing working properly.

We turned up the temp and the next morning when we went out to use the spa we noticed the 'solid' FLO message. http://cpresourcesllc.com/sundance-spa/sundance-error-code-616.php Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. HotTubsByArcticSpas 40.275 görüntüleme 3:41 Hot Tub Not Hot Enough? 104° Temperature Override (:1:) Sundance Spas pre-2009 - Süre: 5:41. Yükleniyor... Sundance Spa Troubleshooting Fl1

Try to reset power to spa. Spaminator provided by [OzzModz] Spaminator - vBulletin Mods & Addons Copyright © 2016 OzzModz Ltd. Otomatik oynat Otomatik oynatma etkinleştirildiğinde, önerilen bir video otomatik olarak oynatılır. http://cpresourcesllc.com/sundance-spa/sundance-spa-code-fl1.php If condition persists, contact your Sundance Spas dealer or qualified service technician.

The first one is for the ozone, the second is for the circ pump and so noted on the inside door diagram. Sundance Spa Circulation Pump If debris is present, remove debris, install switch and test system. With a solid flo nothing should work.

Smart Farm 524 görüntüleme 1:17 5 Common Hot Tub Issues and Solutions - Süre: 5:41.

characters left:

Contact Us|Terms of Service|Privacy & Security|About Us|Our Network|Sitemap © 2003-2016 JustAnswer LLC JustAnswer UKJustAnswer GermanyJustAnswer SpanishJustAnswer Japan 426 9459666 Jump to content Existing user? If your spa is in fact overheating then it is caused by one of two things, either the temperature sensor is defective or the relays on the circuit board that operate If condition persists, provide shade for equipment side of tub. Sundance Altamar Flow Switch Logged Hot Tub Forum 'solid' FLO message on Sundance Spa « on: February 14, 2012, 08:17:32 PM » clover Full Member Posts: 475 Re: 'solid' FLO message on Sundance Spa «

This must be repaired only be a Sundance Spas dealer or qualified service technician. If one of these sensors needs to be replaced BOTH should be replaced at the same time. It does not matter if the error message is FLO or FLO2. this content In most cases overheat issues are related to the relays on the circuit board, or the temp sensor has failed and will need to be replaced.

You can check the switch by performing the test below. FLO2 means that this problem has been detected at startup. The latest failure occurred about 2 weeks ago. I wish I could tell you what year and model it is, but my best guess is that it is a Capri.

With the circ pump and the main pump on, test switch operation with an ohmmeter in the continuity position, test for continuity across switch terminals. The most common valve; the tee handle valve, will show that the handle is up, but in many cases the gate is still half closed, make sure that it is open Logged clover Full Member Posts: 475 Re: 'solid' FLO message on Sundance Spa « Reply #6 on: February 17, 2012, 11:02:18 AM » Quote from: SerjicalStrike on February 16, 2012, 03:45:05 The small circ pump that is plumbed into your heater sounds like it's definitely the problem if you've already changed out the flow switch as well.

I found it easily at the Sundance site online and keep a copy on my computer for reference. 12K Fiberglass IG, Infinity 4000 automatic cover, SWCG, Hayward Sand Filter, Hayward 1.5 You may be suggesting the relay is stuck "closed", but I think not. FINAL NOTE: Balboa M7 systems have the Temperature Sensor as well as the Hi Limit sensor installed in the heater assembly, one at each end. Credentials confirmed by a Fortune 500 verification firm.

All rights reserved. It is a fairly easy fix for someone that knows how to replace a relay. Spa Guy 1.438 görüntüleme 2:54 5 Common Hot Tub Issues and Solutions - Süre: 5:41. FLO, FL, FLC, FL1, PS, Blinking Lights Pressure Switch or Flow Switch Failure.

Nicholas Rogers 5.329 görüntüleme 1:32 Fixing A Cold Hot Tub... - Süre: 10:12. The most common valve; the tee handle valve, will show that the handle is up, but in many cases the gate is still half closed, make sure that it is open