Home > Sundance Spa > Sundance Spa Error Code 616

Sundance Spa Error Code 616

Contents

Tool Dude Tony 240,260 views 8:43 How ClearRay makes owing a hot tub simple - Duration: 3:04. Mike Tassinari October 14, 2016 Reply I own a 2010 Jacuzzi J300 hot tub and this morning the 616 code flashed on my LED display. allseasonspoolsspas 2,728 views 1:54 Why You Need to Own a Jacuzzi Hot Tub - Duration: 9:31. Sign in 20 2 Don't like this video? weblink

Could indicate a flow problem. Sign in 4 Loading... Heater is shut down, but other spa functions run normally. This feature is not available right now.

Sundance Spa Uv Bulb

Using your instructions above, the 616 code cleared. Wondering what your spa is trying to tell you? SESH = Sensor short, nonfunctional. Sign in to make your opinion count.

jacuzziofficial 13,664 views 9:31 HOW TO DRAIN AND REFILL YOUR SPA OR HOT TUB - Duration: 7:02. Water temperature has reached 118°F. A: This is very much like our "CF" where nothing is actually wrong. Sundance Spa Troubleshooting LF = Persistent low flow problems. (Displays on the 5th occurrence of "HFL" message with 24 hours).

Cheers! 616 Reset Instructions If the error code goes away then clean or replace your filters. A problem has been detected which could cause damage to the hot tub or its components. ICE = Freeze condition. 55°F detected.

To reset your countdown timer hold the Jet 1 and cooler buttons for 3 seconds, you will see your filter cycle indicator come up. Sundance Hot Tub Manual It can typically be found in the filter compartment and is a quick fix. Skip navigation UploadSign inSearch Loading... Press and hold the Jets pump 1 and Cooler (-) button at the same time for 3 seconds. 2.

616 Reset Instructions

The current status of theCLEARRAY System appears on the LCD display, either ON orOFF.2. softcellelectrical 50,158 views 4:15 How to Fix an Air Lock in Your Spa : Pools & Spas - Duration: 3:08. Sundance Spa Uv Bulb Note: If the spa power is interrupted, the duration countdown timer is not affected. Sundance Spa Error Code Flo2 Sign in to add this to Watch Later Add to Loading playlists...

Please try the request again. have a peek at these guys From what I've gleaned, it has to do with the Clear Ray UV system, which is standard in newer models (but was not on mine).It took me a while to figure Add to Want to watch this again later? OH = High temperature condition, has reached 110°F. Sundance Spa Flo Error

th3/39 = On startup indicates water temperature less than 39° F. You can often determine the make of the control system by looking inside the spa's equipment area. Sign in 1 3 Don't like this video? check over here Your filters were just clogged restricting flow through them.

Working... Sundance Spa Troubleshooting Fl1 Sign in Statistics 1,278 views 0 Like this video? SE = Spa operating in Standard-in-Economy Mode.

Do not enter the water.

If water temperature drops 20°F below set temperature, low speed pump and heater activates to bring temperature within 15° of set temperature. If it did, it is time to either deep soak your filters (about 48 hours should do the trick) and clean them really well, or, if they are older than 18 Published on Mar 22, 2013Learn how to replace your ClearRay UV Bulb in this brief tutorial. Sundance Spa Not Heating Press the (DISPLAY) button to return to the water temperaturedisplay.3.

RISK OF HYPERTHERMIA (OVER-HEATING) CAUSING SEVERE INJURY, BURNS, OR WELTS. Sign in Transcript 30,313 views 19 Like this video? Press the Jets pump 1 button to switch from “O3” to “U”. http://cpresourcesllc.com/sundance-spa/sundance-spa-code-fl1.php The Sundance Spa Store Hot Tubs And Leisure 4,839 views 1:30 Ease of Ownership - Sundance Spas - Duration: 3:34.

SpaDayz 17,976 views 7:49 How To Fix the Air Lock on Your Hot Tub Pump | Arctic Spas - Duration: 1:33. Loading... Rare system error. softcellelectrical 118,821 views 9:12 Ultra-violet lamp/Peroxide Spa Sanitation System - Duration: 12:27.

What do I do? The system returned: (22) Invalid argument The remote host or network may be down. Sign in to add this to Watch Later Add to Loading playlists... John Powers 10,494 views 1:36 HOW TO start a jacuzzi when the push button STOPS working/loses it's prime... - Duration: 2:37.

SEoP = Sensor open or disconnected. Rating is available when the video has been rented. One sensor has detected 118° F at heater. You can attach a picture of your current ozone unit and plug here for id purposes.

PSoL = Pressure switch open with low pump. OPEN or SHORTED SENSOR (heater disabled) The main temperature sensor is non-functional. If not, replace the flow switch. Try to reset power to spa.

Spa has shut down. Check for proper water level and for clogged filter (pages 60-62). If the hot tub water is more than -7C cooler than the temperature set point, jets pump #1 and heater will automatically activate to provide freeze protection.