Home > Sundance Spa > Sundance Spa Error Flo

Sundance Spa Error Flo

Contents

Flow/pressure switch is defective.Testing Flow/Pressure SwitchThese steps should only be taken after checking and testing the above steps.Testing Flow Switch(Portofino Models Only) Test the Flow Switch Operation: With the circ pump The cheapest replacement I found was about $100, all the way up to $200+. Most common cause for Watchdog is the Temperature Sensor. That happened to me one time several years ago- and tapping the switch worked, and it been fine ever since. weblink

Smart Farm 524 görüntüleme 1:17 5 Common Hot Tub Issues and Solutions - Süre: 5:41. Uygunsuz içeriği bildirmek için oturum açın. After I posted, the FLO message was on, I dropped the temp setting and I left the cover off over night. Oturum aç Paylaş Daha fazla Bildir Videoyu bildirmeniz mi gerekiyor?

Sundance Spa Flow Switch

Make sure there is nothing in the filter area and turn your GFCI back on again. balboawatergroup 15.536 görüntüleme 4:54 How To Fix Hot Tub Pump Motor Start Capacitor Replace - Süre: 2:45. Mr.

Water was at 100 degrees this morning and everything was normal. The indicator light located on the front cabinet panel of the spa is an early detection system that will notify you when the spa needs immediate attention. If you suspect that this is the case, see the instructions on page 77 under "pump does not operate and icon does." Circuit board temperature has exceeded acceptable limit. Sundance Spa Flow Switch Testing RISK OF HYPERTHERMIA (OVER-HEATING) CAUSING SEVERE INJURY, BURNS, OR WELTS.

If all else fails contact your local Sundance Support Desk to book a diagnostic and repair of your spa. Sundance Spa Error Codes Check interlock jumper located on the sensor harness. If it is allowed, could someone link me to a reputable site with the right replacement part so I don't buy the wrong thing? Spa Guy 24.424 görüntüleme 8:14 How to deal with a flow reading on your hot tub - Süre: 4:24.

If your Topside is displaying a Solid FLO message you will have no water movement in the spa. Sundance Spa Pressure Switch If you can remove the equipment access panels, locate the flow switch to see if it is in the closed position or even moving/fluctuating. The only way to test this is to make sure there is no loose debris in the spa, then pull the filter out and see if the flow error goes away, We have used it A LOT.

Sundance Spa Error Codes

They usually stock parts on their trucks. in the morning the FLO message was gone and it appeared to be functioning normally. Sundance Spa Flow Switch Gezinmeyi atla TRYükleOturum açAra Yükleniyor... Sundance Spa Flo2 Error To check out please select Checkout Now.

John Powers 10.494 görüntüleme 1:36 What to do if your hot tub stops heating - Süre: 1:13. have a peek at these guys See Temperature Sensor Diagnostic Guide:http://www.spaandpoolsource.com/sundancespastemperaturesensordiagnostic.aspx6. Had you done anything in particular before this happened? Contiguous US only - Free Shipping is not available to Alaska or Hawaii. Sundance Spa Troubleshooting Fl1

So my guess is that there's an air lock. Any questions or comments?  Just ask! -Jen Allen [email protected] Tweet Comments are closed. Spa Guy 1.438 görüntüleme 2:54 How to Replace Sundance Spas Circulation Pump - Süre: 6:01. check over here Jets pump(s) operate until the hot tub is out of danger. *Note: The error commonly occurs when the hot tub is first filled because tap water is often very cold.

Just so I understand how the circ pump works - are there two modes of operation? Sundance Altamar Flow Switch All rights reserved. If TFP has helped you, please click to SUPPORT TFP!

Main temperature sensor located in filter bucket is nonfunctional.

It sits 3. The problem is that the only shipping option was FedEx ground, which in reality meant Smartpost. Gently tap it a couple times with the handle of a screwdriver or something similar. Sundance Spa Circulation Pump Kapat Daha fazla bilgi edinin View this message in English YouTube 'u şu dilde görüntülüyorsunuz: Türkçe.

Laurent November 08, 2015 Reply Hi, I have the same problem and tried to remove filter, release the air lock from the bib but still showing "Flo & Cool". Yükleniyor... Çalışıyor... Geri al Kapat Bu video kullanılamıyor. İzleme SırasıSıraİzleme SırasıSıra Tümünü kaldırBağlantıyı kes Bir sonraki video başlamak üzeredurdur Yükleniyor... İzleme Sırası Sıra __count__/__total__ Sundance Flow Switch Replacement Video | How to fix http://cpresourcesllc.com/sundance-spa/sundance-spa-code-fl1.php If you power the spa down and power it back up it may work for a while but will do the same thing again.

I immediately turned the breaker off. To replace it do I need to drain the tub? Ive already replaced the flow switch and just replaced the circulation pump (it was still the original) yesterday.