If you added new hardware recently, remove and replace it to determine if it is causing or contributing to the problem. In some cases, drivers for new hardware are not in the Windows XP Professional Driver.cab library, and you need to provide additional drivers to complete the Windows XP setup successfully. In the registry editor, navigate to the subkey HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Session Manager\Memory Management. 3. Ask ! this contact form
Method 2 - Turn Off Features In BIOS This is for advanced users who know how to get into the "BIOS" of your PC. If the error is still not resolved then try turning off features in CMOS settings 3. Possible Resolutions: # A Stop 0xBE message might occur after installing a faulty device driver, system service, or firmware. If a Stop message points to a category of devices (video or disk adapters, for example), try removing or replacing the hardware to determine if it is causing the problem. #
Simply burn the ISO to a CD or use This Version bootable from a USB flashdrive and boot your system from CD or USB to run the test. If the problem still occurs, your System Memory may be at fault. Yükleniyor...
Your firmware might issue a warning but allow the startup process to proceed. A Stop 0xA message might also be due to failing or defective hardware. CareyHolzman 214.914 görüntüleme 12:42 How to Find What Causes Blue Screen of Death - Süre: 1:33. Stop Code 0x0000000a Windows 7 This can cause the Stop 0x0000000A error as XP will be unable to read the hardware references that your system has.
Select the drivers that are incompatible with Windows XP and click on the remove button. 0x0000000a Error Using updated software is especially important for multimedia applications, antivirus scanners, and CD mastering tools. Error Causes The stop 0x000000A error is triggered due to multiple reasons. If this resolves the Stop error message, continue to step c.
DEE Z 185.695 görüntüleme 1:36 How to Fix Blue Screen of Death Stop Error 0x00000024 - Süre: 1:47. Stop Error 0a Windows 7 A similar Stop message, 0x23, exists for the file allocation table (FAT16 or FAT32) file systems. Microsoft KB articles: STOP 0x000000D1 Error Message When You Turn Your Computer Off STOP 0xD1 Error Message When You Start Windows XP STOP 0xD1 Second Mylex AcceleRAID SCSI Controller Causes Error This might indicate a hardware problem with the video adapter or a faulty video driver.
Bu videoyu Daha Sonra İzle oynatma listesine eklemek için oturum açın Ekle Oynatma listeleri yükleniyor... Microsoft KB articles: STOP 0xBE Qwestdex Dex Toolbar not totally compatible with Windows XP Stop 0xC2 or BAD_POOL_CALLER The Stop 0xC2 message indicates that a kernel-mode process or driver incorrectly attempted 0x0000000a Windows 7 From Recovery Console, remove temporary files (those with .tmp file extensions), Internet cache files, application backup files, and .tmp files generated by Chkdsk.exe or Autochk.exe. Printer Error 0x0000000a If this is the case, turn on the setting after you install Windows XP, you are finished.
If a driver is listed by name, disable, remove, or roll back that driver to confirm that this resolves the error. weblink If this works, then that’s great! Possible Resolutions: Stop 0x77 messages can be caused by bad sectors in the virtual memory paging file or a disk controller error. If the first and third parameters are zero, the stack signature in the kernel stack is missing, which is an error typically caused by defective hardware. Irql_not_less_or_equal 0x0000000a Windows 7
For systems with more memory, do not increase the SystemPages value above 110000 without contacting Microsoft technical support. Turn off Features in CMOS Settings Turn off all the following features in the CMOS settings: All caching, including L2, BIOS, internal/external, and write back caching on disk controllers Plug and Periodically check Event Viewer for error messages related to SCSI or FASTFAT in the System log or Autochk in the Application log. # Verify that the tools you use to continually navigate here To increase the number of PTEs allocated in the registry 1.
How To Fix “BAD POOL CALLER” - 0x000000C2 BSOD? Bsod 0x0000000a Windows 7 Check for the availability of updated driver or application files and consult the hardware or program documentation for minimum system requirements. # Another cause is excessive demands for system PTE by Microsoft KB articles: STOP 0x000000ED Error Message When Volume on IDE Drive with Caching Enabled Is Mounted STOP 0x000000ED UNMOUNTABLE_BOOT_VOLUME Error Message Stop 0xC0000221 or STATUS_IMAGE_CHECKSUM_MISMATCH This Stop message indicates driver,
This error also occurs when using mismatched files, such as copying a multiprocessor HAL on to a system using a single-processor kernel (or vice versa). Many Advanced Configuration and Power Interface (ACPI) issues can be resolved by updating to the latest firmware. Click on the Close button and restart your computer. Error Code 0x0000000a Stop 0x0000007B or INACCESSIBLE_BOOT_DEVICE The Stop 0x7B message indicates that Windows XP has lost access to the system partition or boot volume during the startup process.
Using updated software is especially important for multimedia applications, antivirus scanners, DVD playback, and CD mastering tools. # A Stop 0xC2 messages might also be due to failing or defective hardware. You can also choose to install additional applications to another hard disk with more free space or move data files, paging files, and so on. # The problem might be due After you have successfully installed Windows XP, contact the hardware manufacturer to obtain compatible updates. his comment is here Oturum aç 39 Yükleniyor...
If a Stop message points to a category of devices (such as disk controllers, for example), try removing or replacing the hardware to determine if it is causing the problem. # For systems using the FAT16 or FAT32 file system, you have the option of using a Windows 98 or Windows Millennium Edition Emergency Boot Disk to access the hard disk. Windows XP Professional provides a registry entry, SystemPages, that you can use to increase the number of PTEs allocated. If it does, contact the hardware manufacturer for a possible update.
If not, use Recovery Console to manually delete the system service file that is causing the problem. Help!!!!! If all else fails, take the system motherboard to a repair facility for diagnostic testing. Update the drivers of the hardware installed on your system. 5.
Possible Resolutions: # Stop 0x1E messages typically occur after installing faulty drivers or system services, or they can indicate hardware problems, such as memory and IRQ conflicts. In Check disk options, select the Scan for and attempt recovery of bad sectors check box.